| Home Page | Recent Changes | Preferences

2D Shape Editor

2D shape editor tutorial

This is the Industry Standard: [Machismo's 2D Shape Editor Tutorial]

Tarquin: Machismo has invited the Wiki to import his 2D-ed tute. I'm realizing just how much info there is on this topic (eek!)... so I've split off a new page to cover drawing techniques, and added some architecture tutes. Anyway, I'm off to get fud and chill as I've been wiki-ing most of the afternoon...


The 2D Shape Editor was introduced as experimental in the original UnrealEd, but, by the current 436 Version, has matured into a robust tool for creating 3 dimensional shapes. However, it can be crashed ( See, section: Crashing UnrealEd), but, otherwise, is functional and commonly useful to mappers for all kinds of creative brush operations.

This is a versatile 3 dimensional tool. When the 2D Shape Editor is opened, a 2 dimensional grid is displayed, similar to the main UnrealEd 2D grid views. The only real disadvantage is that all vertex points must coincide with the grid (you can't just place the vertices in any position). However, you can map to a small resolution (4 world units), and the resultant 3D brushes are completely at home in the main UnrealEd 3D views.


Starting point for using this tool:

Using the 2D editor to make complex architecture:


For the menu commands, see 2D Shape Editor Menu.

  1. New, Open, Close. 2D shapes can be saved as special 2DS files, independently of the current map in the main UnrealEd window.
  2. Rotate the shape 90 or 45 degrees.
  3. Flip the shape in x or y axis
  4. Enlarge or shrink the shape by a factor of 2
  5. Zoom in or out on the shape (note: the grid is a little buggy on different zoom levels, it's sort of sticky)
  6. Add a vertex by splitting the current sides. If more than one side is selected, will split all.
  7. Remove selected side(s). Note that this tends to rearrange the remaining vertices quite a bit, so it's best avoided if possible as a fair amount of fine tuning is necessary afterwards. Not disastrous, but annoying.
  8. Convert the current side to a linear segment
  9. Convert the current side to a Bezier segment
  10. Process: Sheet
  11. Process: Revolve
  12. Process: Extrude
  13. Process: Extrude to point
  14. Process: Extrude to bevel

Mouse control

  • Click on points to select them.
  • CTRL+Click to select multiple points
  • Click + drag to move points, add CTRL to move multiple
  • Right-click + drag to pan the work area
  • CLick and drag the orange centre point to move the entire shape

Processing commands


This simply creates a sheet brush out of the current shape.


Revolves your 2D brush around the "Y" axis. The origin of the shape (the green node) must be completely to the left or right of the shape you wish to revolve. The distance of the origin to the edge of your shape determines the inner radius the resultant shape. The two properties you specify at the point of revolution are "Per 360" which specifies the number of sides that would exist in a full circle, and "Use" which specifies the number of sides to actually generate.

Tip: rotate the shape before revolving to make, for example, a corridor that curves upwards.

Extrude to set depth

Produces a prism of a given depth, with the current shape as cross-section. It's well worth the effort of extruding the brush slightly deeper than you need and then substracting (or clipping) the "flat" faces of your extruded brush away. The Intersect tool can then be used to grab the final brush and hey-presto you've removed a lot of unecessary polygons. This is similar to the merge polygons command but also changes the brush wireframe potentially reducing the Node Count of your brush.

Extrude to point

Produces a cone with the base of your 2D shape. The height of the code is determined by the depth value specified at the point of extrusion. The X and Y offset of the point of the cone is determined by the location of the 2D shape's origin (that little green node you can see).

Extrude to bevel

This behaves in a very similar manner to that of the "Extrude to point" function. The difference being that the resulting "cone" is trimmed down to the CapHeight specified at the point of extrusion.


Simplify the surfaces of a brush produced with the 2D shape editor with the merge polygons command.

To get rid of extra polygons that it produces when you add the brush, add it then intersect it. Delete the added brush and add the RBB (Red Builder Brush) where you want to add it.

Be VERY careful creating the shape because there are no undo's; save often.

Tarquin: not necessarily a good thing though, may introduce new BSP cuts. Use with caution on complex shapes.

Category Mapping

The Unreal Engine Documentation Site

Wiki Community

Topic Categories

Image Uploads

Random Page

Recent Changes

Offline Wiki

Unreal Engine

Console Commands


Mapping Topics

Mapping Lessons

UnrealEd Interface


Scripting Topics

Scripting Lessons

Making Mods

Class Tree


Modeling Topics


Log In